Chapin 20000 Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement pour l'eau Chapin 20000. Chapin 20000 User Manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Hazard: Improper use or failure to follow instructions can result in explosive failure causing serious eye or other
injury. For safe use of this product you must read and follow all instructions. Do not leave a pressurized sprayer in the hot
sun. Heat can cause pressure build-up. Do not store or leave solution in tank after use. Always wear goggles, gloves, long
sleeve shirt, long pants and full foot protection when spraying. Never use any tool to remove pump if there is pressure
in sprayer. Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than the original
pump. Do not attempt to modify or repair this product except with original manufacturer’s parts. Never spray flammable
materials or heat, pressure, or gas producing chemicals. Always read and follow manufacturer’s instructions before
use with this sprayer as some chemicals may be hazardous when used with this sprayer.
WARNING!
Sk-1113-1
1. Hose to Tank
2. Nozzle / Extension Wand
Attach nozzle to shut-off handle or extension wand per
Fig. 2A-2D depending on the style of extension wand
included with sprayer.
3. Filter
e filter helps prevent clogging while spraying. It is located on the end of the outlet tube
inside your sprayer tank.To clean filter, remove the discharge assembly from the tank
(Fig.1A). Make sure the filter is positioned at the bottom of the tank as pictured (Fig. 3A).
Note: Filters are not supplied with deck sprayers.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose
before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of
deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in
explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not attempt
to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and
inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,
Pressurizing and Spraying Instructions.
5. Pre-Use Check
6. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
8. To Release Pressure
Sprayers with no pressure release valve
Do: With pump facing away, turn locked handle counterclockwise until air begins to escape. Stop turning handle when
you hear air escaping. Do: Point pump away until all air has escaped.
9. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and Spraying
Instructions, except pump unit only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known to the State
of California to cause birth defects and other reproductive harm. Wash hands after handling.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions?
Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?
No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ?
Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
010328 (A) R0110
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Discharge/ Tool Holder Assembly
• Insure the tool holder is assembled to the tank adapter before mounting the discharge assembly (Fig.1A). e Tool Holder
snaps into the groove of the tank adapter. Figure 1D shows how the shield and cup are mounted (Not all models are pro
vided with tool holder, spray shield and measuring cup).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1A).
• Firmly insert the outlet tube portion into the tank adapter (Fig. 1B) leaving no gap between the tank adapter and outlet
tube adapter. Firmly tighten the retaining nut to the tank adapter (Fig. 1C).
WARNING!
To prevent hose from blowing off, hose must cover both barbs on the outlet tube adapter and touch flange
(Fig. 1B) before hose nut is securely tightened (Fig. 1C).
1A
1C
Retaining Nut -
Securely tightened.
Tool
Holder
Measuring
Cup
Spray
Shield
1D
Tool
Holder
Outlet
Tube
Discharge
Assembly
2A
Filter
3A
4. Shield Attachment to Wand
Snap shield onto wand as shown. Using the spray shield will help protect your plants
etc. from over spray. (Not all models are provided with spray shield).
4A
Parts, Piezas, Pièces
6-2001
Hose Kit: 2 nuts, 2 barbs and hose
Juego de manguera: 2 tuercas ,2 lengüetas y manguera.
Nécessaire de tuyau: Deux écrous, deux ardillons et tuyau
6-5364
Measure Cup
Taza para medir
Tasse à mesurer
6-2000
Shut-off Handle
Mango de cierre
Poignée du robinet
6-5385
Spray Shield
Pantalla de pulverización
Bouclier de pulvérisation
6-6003
Nozzle
Boquilla
Buse
7. Pressurizing and Spraying
Do: Turn handle clockwise
to tighten. Push handle
down, turn 1/4 turn coun-
terclockwise to release.
Do: Pump until
you feel resistance.
Do: Push handle, down, turn
1/4 turn clockwise to lock.
Begin spraying. Re-pump
sprayer as required to maintain
spray force.
Do: Turn end of nozzle
to adjust spray pattern.
7A
7C
7B
7D
010842
Tool Holder
Soporte para la
herramienta
Porte-outils
1B
No Gap
Tank
Adapter
Outlet
Tube
Adapter
2 piece style
or
6-4645
Relief Valve
Válvula de descarga de
presión
Soupape de
décompression
6-4566
Four Position Nozzle
Boquilla de 4 posiciones
Buse à 4 positions
6-3337
Straps
Tirantes
Sangles
6-7756
Extension wand (brass)
Vara de extensión
Lance de rallonge
301120-4
Fan Nozzle
(brass tip)
Boquilla
Buse
3-4843
Fan Nozzle Pack
Paquete de boquilla a
chorro
Ensamble de buse à jet
éventail
Filter
Pull handle straight up.
Insert notches from
underside of handle
into plunger grooves
and turn counter-
clockwise.
Remove plunger and diaphragm.
Clean plunger, diaphragm
and body. Flip diaphragm and
replace.
Tighten plunger clockwise until
flush to top of shut-off body.
Do not over-tighten or unit
may not spray. Slide forks un-
der plunger, push handle down
until it snaps into place.
11. Troubleshooting
-
Tank pressurizes but does not spray.
11A 11B 11C
Handle
Plunger
Body
Diaphragm
11D
Plunger flush
with body
WARNING:
Release pressure in tank before troubleshooting.
Clean Nozzle Assembly (Fig. 11E)
-Remove nozzle cap. Clean and re-assemble.
Clean shut-off (Fig. 11A- 11D)
10. Fatigue-Free Spraying
For constant spraying, push down on shut-off handle and move grey locking
mechanism away from you. To release, squeeze handle and move the grey locking
mechanism back towards you. ( Not all models are provided with this feature).
2F2E
Red,
Fine spray for
finer washes
Blue,
Medium spray for
sealers
Yellow,
Course spray for semi-
transparent stains
Attach cap to shut-off handle or extension wand (Fig. 2F-2G).
8A
8B
Do: Point valve away from you when releasing pressure.
2D
1 piece style
Deck Sprayers Only ( Fig. 2D-2G)
Insert nozzle into cap (2E).
10A
2G
Locking
mechanism
Sprayers with pressure release/relief valve
Fig. 8A: Lift and hold the cap OR, turn the valve slowly counterclock-
wise until air is completely exhausted.
Fig. 8B: Pull up stem until air is completely exhausted.
11E
Nozzle Cap
6-7749
Extension wand (poly)
Vara de extensión
Rallonge
6-8156
Relief Valve
Válvula de descarga de presión
Soupape de décompression
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-1925
301272-1
Nozzle
(brass tip)
Boquilla
Buse
2B
2C
1
2
Résumé du contenu
Page 1 - WARNING!
Hazard: Improper use or failure to follow instructions can result in explosive failure causing serious eye or other injury. For safe use of this prod
Page 2 - ADVERTENCIA!
2. BoquillaEncaje la boquilla en la manija de la unidad de cierre o la vara de extensión (Fig. 2A-2D).• Introducir la boquilla en la tapa (Fig. 2E).•
Produits connexes et manuels pour Équipement pour l'eau Chapin 20000
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.660 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels